Summer sale · up to 25% off select batteriesShop Deals →

Installation & Safety Guide

Five steps to a safe install — and the rules that keep your warranty valid.

⚠️

Read before you install. LiFePO4 batteries are maintenance-free but not abuse-proof. Follow the five steps below and keep the do's & don'ts — violations listed under "Don't" can void your 1-Year warranty.

Install in 5 steps

1
Match the voltage

12V battery for a 12V system, 24V for 24V — never connect a battery with a higher voltage than your device rating. If you're replacing lead-acid, match the system voltage and confirm your charger (see step 4).

2
Check fitment & terminals

Confirm the BCI group size fits your tray and the terminal type matches your cables (M8 bolts on most CBJJ models). Most LiFePO4 packs can be mounted in any orientation — no liquid electrolyte, nothing to spill — just keep the terminals protected and accessible.

3
Connect polarity correctly

Red (+) to positive, black (−) to negative. Tighten M8 terminals to 9–11 N·m (80–97 in-lb) — snug, not strained. Over-torquing cracks the terminal seal; loose connections cause heat. Re-check tightness after the first 2 weeks of use.

4
Pair with a LiFePO4 charger

Use a LiFePO4 charger with the correct CC-CV profile for your platform (see the table below). A lead-acid charger with desulfation or equalization mode can damage the BMS — disable those modes or switch chargers.

5
Secure & test

Fasten the battery with hold-down straps or the tray bracket, re-check all connections, then power on to verify normal operation. A short test run before full use catches wiring issues early.

Charger settings at a glance

Set your charger to the absorption (CC) voltage for your platform. LiFePO4 cells sit at 3.2V nominal and finish charging at 3.65V/cell — the classic setpoint — while some chargers use a gentler 3.6V/cell; both fully charge a CBJJ pack:

12V packs (12.8V) — Charge at 14.6V (3.65V/cell; 14.4V chargers also fine) · float ≤ 13.6V or off
24V packs (25.6V) — Charge at 29.2V (3.65V/cell; 28.8V chargers also fine) · float ≤ 27.2V or off
36V packs (38.4V) — Charge at 43.8V (3.65V/cell; 43.2V chargers also fine) · float ≤ 40.8V or off
48V packs (51.2V) — Charge at 58.4V (3.65V/cell; 57.6V chargers also fine) · float ≤ 54.4V or off

Storage & everyday care

Operating temperature

Charge: 0°C to 50°C (32°F to 122°F). Discharge: −20°C to 60°C (−4°F to 140°F). Below 0°C the BMS cuts charging automatically and resumes at 5°C — this protects the cells. Self-Heating models pre-warm the pack so charging works in freezing weather.

Storage

Store at 50–60% charge in a cool, dry place. Top the battery up every 3 months during long storage — letting it sit at 0% for months can push cells below the recoverable floor, which is not covered under warranty.

Series / parallel

Only connect identical CBJJ models — same voltage, capacity and purchase batch — up to 4 in series or 4 in parallel. Never mix LiFePO4 with lead-acid batteries, and never mix old and new packs.

Starting engines

Standard deep-cycle models are not starting batteries — don't use them to crank engines unless your model is explicitly rated Dual Purpose (CCA).

Safety do's & don'ts

✓ Do

  • Charge fully before first use
  • Use a LiFePO4-compatible charger (CC-CV)
  • Secure the battery and re-check terminals after the first 2 weeks
  • Store at 50–60% charge in a cool, dry place when not in use

✕ Don't

  • Don't short-circuit the terminals
  • Don't charge below 0°C (32°F) — the BMS will cut charging; wait for the temperature to recover
  • Don't mix with lead-acid batteries in series or parallel
  • Don't use a standard deep-cycle model to crank an engine — Dual Purpose (CCA) models only
  • Don't disassemble or modify — this voids the warranty
Downloads

Every CBJJ model's installation guide and spec sheet is available on the Manuals & Downloads page — search by SKU or model name. A printed quick-start card is also included in the box with each battery.

Stuck during installation?